FAQ

1. In what sizes is Weldbond^® available?

Weldbond ^® is available in numerous sizes for various applications and project needs. Bottles: 2oz/60 ml, 4 oz/114 ml, 8oz/227 ml, 12oz/341 ml, 21oz/600 ml, 64oz/1/2 gallon/1.82 litres, 128 oz./ 1 gallon Tubes: 1oz/30 ml, 5oz/150 ml, 9oz/275 ml

2. Can I keep my Weldbond^® bottle outside in the garage? Will it freeze?

Weldbond ^® should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°F/ 10°C at all times. Also, after container has been opened, ensure it is closed tightly after each use.

3. How long is my Weldbond^® bottle good for?

Weldbond ^® typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We then advise the consumer to shake like crazy prior to every use until the container is depleted.

4. Is Weldbond^® non-toxic?

Weldbond ^® has been tested to be non-toxic. Weldbond^® conforms to ASTM D4236.

5. How can I access the Weldbond^® MSDS?

You can access the Weldbond ^® MSDS via the Weldbond^® website, click here.

You can also send us an email to info@franktross.com requesting the document and we will forward you an electronic copy.

6. Is Weldbond^® tested on animals or created with any animal by-products?

Weldbond ^® is not tested on animals and does not contain any animal by-products. This product is Vegan Friendly.

7. What does the EcoLogo™ stand for?

EcoLogo™ certifies that Weldbond ^® has been tested for environmental safety and performance under CCD 046 – General Adhesives. EcoLogo™ is a 3rd party certification seal that certifies products based on strict standards. To read more about EcoLogo™, click here.

8. What is meant by porous and non porous surfaces? How can I tell which is which?

A porous surface means that the material is full of tiny holes that allow fluids or gases to pass through, non porous surfaces do not allow anything to pass through.

Porous surfaces must be sealed with 1 part Weldbond ^® to 5 parts water. Porous surfaces can be determined by dropping a small amount of water on surface. If water is readily absorbed, surface is porous. If water beads on the surface, it is non porous.

NOTE: The sealing mixture of 1 Weldbond^® to 5 water should not be used where water alone would have an adverse effect, i.e. on water soluble fillers.

9. Are there any materials that Weldbond^® can’t glue?

Some types of plastic, rubber and cast metals will not produce a bond with Weldbond ^® , i.e. polyethylene, unbacked vinyl, P.V.C., Teflon^®, polypropylene, vinyl to vinyl, cast iron, cast aluminum. Weldbond® is not intended for marine applications. It is not recommended for use on exposed exterior surfaces. Garage interiors are acceptable.

NOTE: Do not use when bonding containers designed for use with, or subject to, hot liquids.

10. How do I remove Weldbond^® from my clothes, carpet, curtains or anything else?

Weldbond ^® is a water based glue therefore if the stain/spill is recent we recommend using cold water, not hot water. However once the glue has set it is very difficult to remove therefore be sure not to wear your favourite clothes while using Weldbond ^®, just in case!

11.How do I dissolve Weldbond^®?

Weldbond ^® can quickly be dissolved with acetone. Because Weldbond^® is water based it can also be dissolved with a soaking of, or submersion in water. This will dissolve a bond.

12. Can Weldbond^® be tinted?

We have many craft users that tint Weldbond ^® with a wide variety of creative methods, including tea, paint, nail polish and other creative methods. We always recommend the consumer to test this creation on a small piece prior to proceeding with the full project. Some compounds utilized for tinting could have an adverse impact on the makeup of the Weldbond ^®.

13. What kind of paint will seal Weldbond^®

We recommend Latex and Acrylic paints for the best results.

14. Can Weldbond^® be utilized on external applications?

Weldbond ^® can be used on external applications as it is weatherproof. However, Weldbond^® is not waterproof, it is water resistant. Weldbond^® should only be used on external applications if it is free of standing water that could cause it to freeze or if it is being used on a vertical surface where water cannot pool on top.

15. Can Weldbond^® be utilized on marine applications?

Weldbond ^® is not intended for marine applications. It is not recommended for use on exposed exterior surfaces.

16. My Weldbond^® project bond has not dried clear.

a. Why not?

Most like too much adhesive was used. Another possibility could be that if you are gluing a large surface, air cannot get to the Weldbond ^® in the middle of the bond. We do suggest that if you are gluing large pieces, you apply the adhesive to the exterior rim and not the centre as a proper bond might not take place.

b. What can I do about it?

Apply heat. If weather conditions permit, set the project in the sun. For large glass surfaces, glue the edges, but stay away from large amounts of glue through the middle of the surface. Weldbond ^® air cures.

17. Does Weldbond^® release any fumes?

Weldbond ^® does not release any fumes no matter if it is in liquid or solid state.

18. What is the set-up time?

The set up time for tackiness will vary with humidity, but is roughly five minutes for most projects. It will be somewhat longer in humid conditions.

19. What is the cure time?

Weldbond ^® becomes tacky quickly and will dry within the hour on porous surfaces. Provides a strong bond within 24 hours and tremendous strength within a few days. The sealing mixture of 5 parts water to 1 part concentrated Weldbond ^® dries in approximately 1 hour.

For more information regarding specific gluing jobs, please check the Weldbond ^® Application Uses section.

20. What are the physical characteristics of Weldbond^®?

21. Is this a PVA adhesive or a PVC adhesive?

Weldbond ^® is a PVA adhesive . (Poly Vinyl Acetate based adhesive)

22. Is there any formaldehyde preservative in this adhesive?

Weldbond ^® does not contain any formaldehyde preservative. The EcoLogo™ certification states that Weldbond^® has been created without: latex, aromatic or halogenated solvents, formaldehyde, toxic metals, including but not limited to cadmium, hexavalent chromium, lead, and mercury, or their compounds

23. Is there any phthalates in this product?

Weldbond ^® is created without the use of phthalates and is therefore free of phthalates.

24. What is the VOC content of this product?

Weldbond ^® does not contain more than 1% VOCs by weight. This technical fact is approved and certified by EcoLogo™.